Top 10 common forklift crashes ， forklift procedure ought to take notice of these matters ！.

Do not ignore the forklift at the workplace. If the operation is not good, there will be major mishaps in minutes, and there are lots of mishaps including forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the person in front can not be located, causing a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy products, the employees used their body weight as the counterweight, which almost created casualties.
Instance 3: The size of the forklift cargo surpasses the allowable width of the course and holds on the roadside shelf, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure ought to pay attention to these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver must first validate that the load is secure and reputable.
4. The beginning needs to be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork expensive when driving. When entering and leaving the task website or while driving, be careful that there will be no obstacles overhead. When the load is taking a trip, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the car to shed side security and topple. .
5. When the forklift is downhill, it is purely forbidden to shut off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the manufacturing facility and have to keep a certain safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be appropriately slanted back. The lots will not be increased other than when stacking or packing. .
8. The height of the load must not block the driver's view. In unique conditions, when the thing impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to stand on the fork to hold things and play a stabilizing role. .
12. If problems are located, they will be repaired and reported in a prompt way, and they will never ever run with diseases or hide them.

packing and discharging.
1. When fork-loading items, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not manipulated, and one side of the item need to protest the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or pull. In unique circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When utilizing a fork to fork the goods, the fork needs to be as deep as possible under the lots, and it should be kept in mind that the fork tip ought to not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted ahead somewhat when the lots is lowered to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and ram hard objects with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to stay clear of the collapse of the goods and injure people. .
8. Overloading is forbidden, and it is banned to make use of forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Prior to leaving the forklift, you need to unload the goods or lower the fork frame.
2. Pull the parking brake deal with to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be checked, and fuel, lubing oil and air conditioning water must be added.
2. Check the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, examine whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leak ought to also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the cars and truck;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is greater than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is Stand-on Electric Pallet Stacker not enabled.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to pick up the goods.
6. It is not enabled to make use of braking force to exile round or easy-to-roll things.
7. It is not allowed to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than Stand-on Electric Pallet Stacker 5%.
3. When there is an obstacle on one side of the road, the opposite side of the area with the exact same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844